There are two variants to choose from - one with the weight on the right-hand side and one with the weight on the left-hand side. The tool for adjusting the timing belt tension can also be used for the FLSUN Super Racer (SR), as the timing belt spacing is the same as for the V400. The measurement should be taken at mid-height, between the lower and upper bearing roller of the timing belt.

Start Gcode: START_PRINT BED_TEMP={material_bed_temperature_layer_0} EXTRUDER_TEMP={material_print_temperature_layer_0} A nyomtatóhoz előre telepítve van a Klipper Firmware. A Klipper első osztályú nyomtatási élményt és nagyfokú felhasználóbarátságot biztosít – akár WiFi távirányítóval is! The Cura Profiles were updated by following the details in THIS file and a new V400 added to Cura (this is V400 #2 on my system and has 600mm/s as the max speed.

I feel the need, the need for speed.

A higher belt tension can be set by adding more 50 cent coins, and a lower belt tension can be set by removing 50 cent coins. The printer comes pre-installed with Klipper firmware . Klipper provides a first-class printing experience and ensures high user friendliness – even via WiFi remote control! Installation only takes a few seconds, to verify that the firmware has been successfully installed, the file on the microSD card must have been renamed to ROBIN_NANO35.BIN.CUR and the version on the System Loads tile must have been changed.

To use ADXL345 with FLSUN V400 for measuring Resonances it's necessary to use it via USB with a Raspberry Pi Pico.To adjust manually Resonance Compensation, see here: https://www.klipper3d.org/Resonance_Compensation.html

Note: Access to the microSD port of the motherboard being impossible as it is, because of the pneufit just in front, I modeled a new support available in STL Files section. Motherboard Mount for Easy Access to microSd port: https://www.printables.com/model/268464-flsun-v400-motherboard-mount Get the firmware named Robin_nano35.bin in /home/pi/klipper/out/ directory (on the left part of MobaXterm). Firmware retraction gives an advantage compared to Slicer retraction, it can be modified during a print (from Mainsail or KlipperScreen) and therefore the same gcode can be printed with different parameters without the need to be re-sliced. The FLSun V400 is simple to use, fun to watch and can save you loads of time. I’ve used it a lot for prototyping parts for an RC car I’m building – in draft mode the printer can blaze through filament in a fraction of the time needed on a standard printer. The prints it produces at speed are still of excellent quality, so there’s no reason to limit it to only test prints.Then the new image was written to the SD card using Raspberry Pi Imager, inserted into a fully disconnected Speeder Pad and left to update (took about 20 mins). Finally all the calibration was done again but its easier with the new firmware. Bed Level now does both phases in one go and leaves you with a screen to set Z0. Then goto Config – Input Shaper – there is now an Auto Calibrate button – there is no need to comment out parts of the cfg files or do the SAVE-CONFIG – this is all now done for you. Files are sliced in Cura just like any other printer, then are transferred to the V400 via the Moonraker plugin, dragging and dropping into Mainsail, or by using the supplied USB drive. Printing on the FLSun V400 Once the image is written, turn off Speeder Pad if is on and remove all devices plugged into the USB ports. Klipper is a 3d-Printer firmware. It combines the power of a general purpose computer with one or more micro-controllers. f)Once the image is written, turn off Speeder Pad if it is on and remove all devices plugged into the USB ports.

The Flsun V400 is an extremely user-friendly Delta 3D printer. The 3D printer features extremely fast printing speeds of up to 600 mm/s and an acceleration of 10 000 mm/s². This saves you more than 70% of the usual printing time while still producing high-quality 3D prints.The correct toothed belt tension is indicated by a pointer that is vertical and parallel to the printer frame. In my case, this is achieved with 6 50 cent coins, i.e. 46.8 grams in weight.